De medewerkers van Holland Nautic (Lowrance) en de prostaffers wensen jullie veel plezier op deze HelpDesk

Nieuwe ontwikkelen rond 2D Sonarview 4.0.......

Ga naar beneden

Nieuwe ontwikkelen rond 2D Sonarview 4.0.......

Bericht van Juan Gonzalez op za 16 jul - 6:42

Hallo allen,

Onderstaande bericht is vandaag op het BBC-forum gepubliceerd. Wellicht interessant voor diegene die 2D Sonar problemen ondervinden sinds de 4.0 upgrade.

We did some testing this week on table rock lake.. we found out few things..
1. make sure nothing touching the transducer cable. example the pwr and neg. from the battery.. make sure there not wrap around them. Same goes with the bow.. make sure the wire's not wrap on the transducer cord or touching them. zip tie wire's away from the transducer.
Once we moved all the wire's away from the transducer it all cleared up..we even tested between 3.5 and 4.0.
2..also if you have Minkota fortex and maybe with other newer models of minkota.. Make sure you didn't blow fuse, there's a fused on top of the TM under neath the lid/cap. If that is blows it will pick up more interference: FYI, even the fused blew the TM will still work.
We did not know about the fused inside the TM cap, until the Minkota rep showed us..Yes the Minkota rep was there too.
Jason Gilstrap / Lowrance Pro Staff
Bron: http://www.bbcboards.net/zerothread?id=703312

Vr. grt,

Juan Gonzalez
avatar
Juan Gonzalez
Gold Member
Gold Member

Aantal berichten : 232
Registratiedatum : 15-03-11
Woonplaats : Netherlands

Profiel bekijken

Terug naar boven Ga naar beneden

Re: Nieuwe ontwikkelen rond 2D Sonarview 4.0.......

Bericht van Frenk Elings op ma 18 jul - 6:08

Interesting................TNX

_________________
Beter 1 banaan onder je boot dan 10 in de fruitschaal
avatar
Frenk Elings
SuperAdmin
SuperAdmin

Aantal berichten : 356
Registratiedatum : 01-12-08
Leeftijd : 55
Woonplaats : Hillegom

Profiel bekijken http://lowrance.actieforum.com

Terug naar boven Ga naar beneden

Re: Nieuwe ontwikkelen rond 2D Sonarview 4.0.......

Bericht van Juan Gonzalez op ma 18 jul - 6:34

Update m.b.t. 2D sonar view 4.0. Very interesting...

Jason Gilstrap heeft het volgende bericht geplaatst (BBC):

I got this from the H-bird section, reference there interference problem caused by Minnkota fortex US2 transducer
The motor can be grounded internally but this requires that the motor be disassembled, resealed and reassembled and it is recommended that this only be done by a the motor manufacturers authorized service center.

If you have a trolling motor that has Universal Sonar 2 you need to insure that the fuse in the head of your motor has not blown. A visual inspection will not suffice, you will need to check for continuity with a volt meter. If you do not know where the fuse is located in your trolling motor, you should be able to locate it in the exploded diagram of your trolling motor manual. This fuse is a 3-amp, mini automotive. If the fuse is blown, you should either contact MinnKota Customer Service or one of their many Authorized Service Centers across the US and Canada. Also make sure that the connections on the Universal Sonar Cable are properly tightened. If these connectors are not completely screwed in, noise can enter the unit from these openings.

Fuse location inside Motor Head


US2 Cable inside motor head


External US2 Cable the hooks up your unit adapter:


Vr. grt,

Juan Gonzalez
avatar
Juan Gonzalez
Gold Member
Gold Member

Aantal berichten : 232
Registratiedatum : 15-03-11
Woonplaats : Netherlands

Profiel bekijken

Terug naar boven Ga naar beneden

Re: Nieuwe ontwikkelen rond 2D Sonarview 4.0.......

Bericht van Gesponsorde inhoud


Gesponsorde inhoud


Terug naar boven Ga naar beneden

Terug naar boven


 
Permissies van dit forum:
Je mag geen reacties plaatsen in dit subforum